Bi-Pb-Tl三元系相图

用室温、高温X射线衍射及淬火的方法,测定了Bi-Pb-Tl三元系25℃的等温截面及该体系中的相结构。     

激光合金化熔池成分均匀性与形状系数的关系SCIEI

本文研究了激光工艺参数对镀Cr中碳低合金钢激光合金化熔池形状系数及成分均匀性的影响。实验结果表明,熔池成分均匀性取决于其截面形状系数,后者是光束功率密度和交互作用时间的函数。在功率密度一定时,形状系数与交互作用时间成线性关系。当形状系数为1.6—3.0时,可以获得成分均匀的熔池。     

氢对Ti合金的Debye温度和晶格常数的影响

使用X射线衍射仪测定出不同氢含量的Ti-30Mo合金的Debye特征温度值以及晶格常数的变化,结果表明随着氢含量的增加,Debye特征温度相应地减小而晶格常数增加,证实了氢含量的增加会导致金属原子间键合力的减弱,从而造成金属脆化。     

SOLUTION BEHAVIOUR OF VARIOUS ALLOYING ELEMENTS IN Ni_3Si

The solid solubilities of 15 common alloying elements added to the Ll_2-type intermetalliccompound Ni_3Si at 900°C have been estimated,and their substitution modes have been de-duced from the direction of solubility lobe of the compound.It is shown that the alloyingbehaviours in Ni_3Si are determined by both size and electronic factors,i.e.,the substitutionmode is governed by electronic configuration and solubility by the both.An interactionparameter is presented to describe quantitatively the influence of electronic configuration onsubstitution mode and the solubility limit can be successfully explained together with atom radius.     

二元Al-Li合金的沉淀反应SCIEI

本文通过对两种成分的二元Al-Li合金的硬度测量,DSC分析和TEM观察,研究了其沉淀过程。实验结果表明,在恒定时间时效,合金硬度与温度的关系曲线上在低温范围内有一峰值出现;在DSC曲线低温处有明显的回溶吸热峰,因此该合金低温时效有预沉淀(富Li GP区)形成。在较高温度时效,GP区不复存在;随着δ′相颗粒长大,合金硬度很快增加;DSC曲线上有两个δ′相回溶峰,它意味着δ′析出需有两次结构调整。平衡δ相借助晶界直接从过饱和固溶体中形核长大,其热稳定性较好。     

CHARACTERISTICS OF INTERNAL FRICTION AND MODULUS ASSOCIATED WITH NON-EQUILIBRIUM DIFFUSION-TYPE PHASE TRANSFORMATION IN EUTECTOID Al-Zn ALLOY

The characteristics of the low frequency internal friction and the modulus effect associatedwith the non-equilibrium spinodal pretransformation and the following discontinuous trans-formation was investigated in an as-quenched eutectiod Al-Zn alloy.It was observed that theloss of the stability in the lattice,which corresponded to the large-amplitude long-wavelengthstatic concentration wave in the non-equilibrium spinodal pretransformation,did not induceany effect of localized soft modulus.Although there are two aging internal friction peaks inphase transformation which correspond to the appearance and disappearance of the coherencyin spinodal pretransformation and the maximum of the interface area in the discontinuoustransformation respectively,the effect of localized soft modulus did not take place yet.     

EFFECT OF FINE GRINDING ACTIVATION ON LEACHING BEHAVIOUR OF SCHEELITE CONCENTRATE

The influence of mechanical activation on the leaching behaviour of scheelite was studied bymeans of fine grinding in an attritor and subsequently HCl leaching in presence of PO_4~(3-).Results showed that after fine grinding in the attritor,the reaction rate of scheelitewith HCl-Na_3PO_4 solution was remarkably increased,the extraction of W increased fromabout 8 to 99%.The IR spectra and X-ray diffraction analysis indicated that in addition toan enlargement of surface area the fine grinding action had made also changes of fine struc-ture and reactivity of solid surface,hence the leaching process of scheelite can be carried outunder mild leaching conditions.     

APPLICATION OF MAXIMUM ENTROPY METHOD TO CALCULATE RDF OF Ni-P AMORPHOUS ALLOY FROM X-RAY DIFFRACTION DATA

Experiments clarified that application of the maximum entropy method to calculate the RDF(radial distribution function)of the Ni-P amorphous alloy from fewer data of its X-raydiffraction data shows a higher resolution and good consistent with known results.It is be-lieved that this method is available for the analysis of amorphous structure.     

微重力偏晶合金凝固特征SCIEI

对在微重力条件下获取的Al-In(95wt-%)偏晶合金的显微组织特征进行了分析,结果表明,在空间制取的试样的Al枝晶中,还存在着大量的In质点;并且这些质点的分布具有某种规律性,由此形成了与地基样品显微组织上的明显差异,反映出一种与重力效应相关的材料凝固特性。     

THERMOGRAPHIC ASPECT ON LOADING A THIN-WALL PRESSURE VESSEL STEEL

The infrared emission of a high pressure vessel steel and two thin wall pressure vessel modelshave been investigated by use of vibro-thermography.The experimental infrared cracklengths were found to be agreed closely with the optical values during fatigue process.A possi-ble nondestructive testing method used to evaluate the pressure vessel has been given.